Maxim MAX2742 GPS接收器解决方案

没有公告

	加入收藏
	设为首页
	联系站长

. 网站首页 . 新闻 . 新品 . 方案 . 专访 . 活动 . DSP . EDA . 评测室 . 技术文库 . 会员区 . 商城 . 服务导航 . 邮购 . 资源 .

您现在的位置： 61IC中国电子在线 >> 方案 >> 无线通信 >> GSM手机 >> 文章正文

[组图]Maxim MAX2742 GPS接收器解决方案

热 ★★★

【字体：小大】

Maxim MAX2742 GPS接收器解决方案

作者：Maxim 文章来源：本站原创点击数：更新时间：2007-6-25

Maxim公司MAX2742是CMOS单片GPS前端下变换器,器件的功耗非常低(2.4V时32mW),不需要昂贵的IF SAW滤波器或体积过大的IF基带滤波器.MAX2742集成了低噪音放大器(LNA),混频器,带通滤波器(BPF),自动增益控制放大器(AGC),本地振荡合成器,时钟缓冲器和整数数字取样器.本解决方案提供了完整的GPS前端解决方案.

Complete Stand-Alone GPS Receiver Solution with MAX2742
Abstract: A complete GPS solution is achieved with minimal external components, using the MAX2742 integrated CMOS RF front-end GPS receiver.

The MAX2742 is a CMOS, single-chip, GPS front-end downconverter. This state-of-the-art device consumes very low power (32mW at 2.4V), and eliminates the need for a costly IF SAW filter or bulky discrete IF bandpass filters. The MAX2742 integrates a low-noise amplifier (LNA), mixer, BPF, automatic-gain-control amplifier (AGC), local oscillator synthesizer, clock buffer, and internal digital sampler.
This device can interface with many commercially available GPS baseband ICs. It is suitable for many applications, including vehicle navigation, telematics, automatic security, asset tracking, location-based service (LBS), and consumer electronics. The external components required around the device are minimal for a complete GPS RF solution. The system block diagram can be found in the following section.

The MAX2742 works with an 18.414MHz* crystal or TXCO, and offers differential or single-ended** IF output at 1.023MHz. Total signal conversion gain is 120dB, with a noise figure of 4.5dB. The IF signal is sampled at the reference clock rate of 18.414MHz.

* Note: 18.414MHz is 18 times 1.023MHz, which is one-tenth of the GPS fundamental frequency 10.23MHz.

** Note: There are three IF output pins—one pair of differential outputs and one single-ended output. Selection is controlled by pin 10.

Complete GPS RF Front-End Solution

Figure 1 shows the important building blocks and features of Maxims complete GPS RF solution. Description of the building blocks can be found in Table 1; cascaded performances are shown in Table 2. Figure 2 shows the application circuit of the GPS receiver RF portion with the MAX2742.

Figure 1. GPS RF front-end block diagram.

Table 1. RF Portion System Building Block

Table 2. System Cascaded Performance

Figure 2. GPS RF portion schematic for MAX2742.

Complete Stand-Alone GPS Receiver Solution
There are more building blocks to construct a complete GPS receiver, other than just the RF plus baseband IC. As shown in Figure 3, an extra antenna supply-control block, a RESET circuit, and a delay circuit are needed. Description of the building blocks can be found in Table 3; cascaded performances are shown in Table 4.

Figure 3. Complete GPS receiver solution block diagram.

Table 3. System Building Block

Figure 4 shows the real PCB layout of the reference design. The complete solution only occupies 25mm x 25mm of PC board space.

Figure 4. GPS Receiver PCB layout.

Table 4. Module Performance (LNA + MAX2742 + SONY CXD2932)

Note 1: T.C. = test condition, N.M. = not measured

http://www.maxim-ic.com/appnotes.cfm/an_pk/3447

欢迎点击进入：TI德州中文网 (国内唯一针对TI应用的中文技术网站) 文章录入：admin 责任编辑：admin

上一篇文章： NXP A-GPS手机解决方案

下一篇文章：没有了

【发表评论】【加入收藏】【告诉好友】【打印此文】【关闭窗口】

最新热点		最新推荐		相关文章
				Maxim MAX8671X功率管理解决… Maxim MAX2120机顶盒调谐方案 Maxim MAX3814 TMDS驱动解决… Maxim MAX5952 -48V POE解决… Maxim MAX3580 TV调谐器应用… MAXIM卫星STB调谐器解决方案 UT斯达康 E-Box企业通信解决… Maxim 机顶盒(STB)解决方案

　　网友评论：（只显示最新10条。评论内容只代表网友观点，与本站立场无关！）

站长：61IC 湘ICP备05002478号